ami-sapphire@amisaphlinux:/media/Epic-Drive$ sudo smartctl -a /dev/sde smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-22-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: IBM Deskstar 40GV & 75GXP (A5AA/A6AA firmware) Device Model: IBM-DTLA-307015 Serial Number: YFDYFG48608 Firmware Version: TX2OA5AA User Capacity: 15,361,597,440 bytes [15.3 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-5 T13/1321D revision 1 Local Time is: Mon Jan 16 17:42:22 2017 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 1231) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 10) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 060 Pre-fail Always - 1 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 158 158 024 Pre-fail Always - 115 (Average 74) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 55 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 2 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 5 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 55 192 Power-Off_Retract_Count 0x0032 100 100 050 Old_age Always - 55 193 Load_Cycle_Count 0x0012 100 100 050 Old_age Always - 55 194 Temperature_Celsius 0x0002 211 211 000 Old_age Always - 26 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 2 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 2 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 occurred at disk power-on lifetime: 4 hours (0 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 af cf c9 e1 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- f9 00 01 af cf c9 e1 00 00:02:13.600 SET MAX ADDRESS [OBS-6] f8 00 00 af cf c9 a1 00 00:02:13.600 READ NATIVE MAX ADDRESS [OBS-ACS-3] f8 00 00 00 00 00 e0 00 00:02:10.900 READ NATIVE MAX ADDRESS [OBS-ACS-3] 10 03 01 01 00 00 a0 06 00:02:10.900 RECALIBRATE [OBS-4] 10 03 01 01 00 00 a0 06 00:02:10.800 RECALIBRATE [OBS-4] Error 1 occurred at disk power-on lifetime: 4 hours (0 days + 4 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 51 01 a4 8f c9 f1 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- f9 00 01 a4 8f c9 f1 00 00:02:23.900 SET MAX ADDRESS [OBS-6] f8 00 00 af cf c9 b1 00 00:02:23.900 READ NATIVE MAX ADDRESS [OBS-ACS-3] f8 00 00 00 00 00 f0 00 00:02:19.800 READ NATIVE MAX ADDRESS [OBS-ACS-3] ec 00 01 01 00 00 a0 06 00:02:19.700 IDENTIFY DEVICE ec 00 01 01 00 00 a0 06 00:02:19.700 IDENTIFY DEVICE SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Selective Self-tests/Logging not supported